Pleated Shades

Pleated Shades Serving Mooresville, IN

One creased layer, priced and explained honestly

Call (317) 999-5154Get Free Quote
Quick Answer

These are the questions we field most often about this product. Several of the answers include a caveat. That's deliberate, because a caveat before the sale is far cheaper than a complaint after one.

  • Service: Pleated Shades for Mooresville homeowners
  • Service area: Mooresville, IN and surrounding areas
    • We book measures without much delay. What you can't compress is the fabrication window, which runs two to five weeks depending on the product and the finish. Painted shutter finishes sit at the longer end.
  • Insured and bonded
  • Serving Mooresville, IN since 2008
Pleated Shades Services

Expert Pleated Shades for Mooresville Homes

Pleated shades are a single creased fabric on a lift system, and they belong to a particular moment in this town's building history. Mooresville put up just 198 houses in the whole of the 1980s, a 4.7 percent trough between the 1960s ranch wave and the 1990s wave, and pleated shades were the standard product of exactly that era. They're still the right call in specific rooms today. Against a median owner occupied value of $206,400, which sits fourth in this five town set behind Greenwood's $276,100 and ahead of Shelbyville's $174,700, a pleated shade puts a decent custom fabric in a secondary room without spending like a front room.

The disclosure is straightforward and it's the reason cellular exists. A pleat is one layer of folded cloth with air on both sides of it, not a cell holding a pocket of trapped air, so the DOE and Oak Ridge finding about cellular shades saving up to 20 percent of heating energy against a bare window does not describe this product. Buy a pleated shade for light and for looks. There's a second point about aging: the creases relax with years of cycling, so an old pleated shade hangs softer than a new one, and the cord routing holes pass pinpricks of daylight even when the shade is fully down.

When to Call

Signs You Need Pleated Shades

If you notice any of these in your Mooresville home, it is worth booking a measure. None of it is urgent, and none of it fixes itself either.

A stairwell window is too high to reach safely

Route holes glow in a line after dark

Trim is too shallow for a deeper headrail

The shade creeps down an inch overnight, every night

An office window needs cover but not insulation

An angle top window never had a shade that fits

The cord lock has to be reset every single morning

An arched window has never been covered

Cellular quotes came back higher than the room needs

Cheap stock shades were cut to the nearest inch

Our Process

How Mooresville Window Treatments Handles Pleated Shades

Every job follows the same five-step process. Transparent, thorough, and done right the first time.

1

Mounting depth read

2

Route holes or cordless decided

3

Full travel run twice per unit

4

Specialty shapes templated on site

5

Whole room ordered on one purchase

Real Project Photos

Pleated Shades in Mooresville

Photographs from real pleated shades jobs completed by our crew in Mooresville and surrounding areas.

Custom shades measured and installed in MooresvillePlantation shutters fitted to a Mooresville windowCellular shades in a Mooresville living room
Scope of Work

What Pleated Shades Includes

Every Mooresville job is documented item by item. Here is what the crew covers.

The energy question answered honestly up front: a pleated shade is one layer of fabric with no cell behind it

Rooms steered to cellular instead wherever trapped air is the actual reason for the purchase

Rooms where pleated is the right call identified plainly, from secondary bedrooms to offices to a rental turnover

Pleat size set against the opening, a fine pleat on short glass and a larger pleat where the drop can carry it

Fabric opacity settled in writing before the order, light filtering against room darkening

Reflective backing considered on hard west and south exposures, described as what it is rather than as an energy rating

Three widths and three heights per opening with a diagonal check for square

Mounting depth read so the headrail sits inside the opening where an inside mount is what you want

Stack at the top measured against the glass, since a stacked pleated shade still covers the top few inches

Cordless lift specified in rooms children use, with products conforming to ANSI/WCMA A100.1-2022 for cord access

Route holes disclosed on any corded unit, because a closed pleated shade shows those holes as a line of small bright dots

Light gap per side written onto the paperwork, along with the 1/16 inch per side factory deduction Lutron publishes

Top-down bottom-up priced where a room wants daylight high and cover low

Arched, angled and fan-shaped openings templated on site, since pleated fabric is what those get built from

Wide spans reviewed for headrail deflection and split into two units where that is the right answer

Every opening in a room ordered on one purchase so the fabric comes off the same run

The paperwork done properly, with IC 24-5-11 requiring scope, dates and total price on residential jobs over $150

Bottom rail leveled and full travel run twice at every unit before we pack up

Pricing

What Pleated Shades Cost in Mooresville

National category figures put stock shades near $60 to $600 a window and custom-fabricated shades roughly $250 to $2,600. Those are published national ranges, not a price for any opening in Mooresville. Pleated sits low in the custom band and that is the honest appeal of it. One layer of fabric, a light headrail and a simple lift add up to less than a double cell shade with a blackout fabric and two lift systems. Where the number climbs is the same place it climbs on everything: width, drop, a room darkening fabric, a cordless lift on a heavy unit, or a templated arch that somebody has to build to a pattern. Mooresville Window Treatments prices from measured openings across Morgan County rather than from a per-window average.

By Product

How Pleated Shades Differ by Product

Every product in this trade behaves differently in a room. Here is what that means for this work.

1 inch pleat: The standard and the one most rooms get. It holds a crisp horizontal line at ordinary window heights, it stacks small at the top, and it keeps the scale right on the bedroom and office windows this product usually goes into.

Fine pleat: A smaller fold for short windows, transoms and specialty shapes. More folds across the same drop means a finer face, and it's what a small arch or a narrow sidelight needs so the shape doesn't look coarse.

2 inch pleat: A larger fold that suits tall glass and big rooms, where a fine pleat across a long drop starts to read as texture rather than as a line. Fewer folds also means a slightly smaller stack for the same height.

Light filtering fabric: The everyday specification. Diffused daylight comes through, the view does not, and the room stays bright. It's the fabric that suits an office, a stairwell or any bedroom where waking up with the sun isn't a problem.

Room darkening fabric: A denser fabric that cuts most light through the face. It gets a bedroom dim rather than dark, since a pleated shade doesn't seal at the edges and an inside mount still passes light down both sides.

Reflective backing: A metallized back face that bounces some of the sun striking the shade back at the glass. It's a real property of the fabric and it's not an energy rating, and we describe it that way rather than putting a number on it.

Cordless spring lift: A spring lift with no operating cord on the product, and the version we specify in any room a child uses. It also removes the route holes from the conversation, since there's no lift cord passing through the fabric.

Corded lift with a cord lock: The traditional and least expensive control. The lift cord runs through holes punched in the pleats, which is exactly where a closed shade shows a vertical line of small bright dots at night. Worth knowing before you save the money.

Top-down bottom-up: Two rails on one shade, so the top can drop for daylight while the bottom stays up against a sidewalk. It adds a second lift system and its own hardware, which is where much of the extra cost comes from.

Fixed arch and angle-top units: A half-round, a quarter-round or an angled top built to a site template and left fixed. Pleated fabric is what these get made from, because a pleated fan holds its shape where a rolling product simply can't follow the geometry.

Light Control

See What Each Fabric Does To The Light

Pick a fabric below and the window updates. It's a drawing rather than a photograph, so read it as a rough guide to what each family does in a Mooresville room, and to what it doesn't do.

Fabric type

Sheer, 10 percent openness

Ten percent of the weave is open, so you keep the view and most of the daylight. Glare drops a little. After dark, once your lamps are on, someone outside can read shapes through it, which is why this belongs on a view window rather than a bedroom.

Openness factor is printed on the fabric card, so you can compare one line against another before you order anything.

Keeps the viewNot private after dark

Solar, 5 percent openness

The usual pick for a west window or a covered porch. You can still read the yard through it, glare comes down noticeably, and the fabric intercepts a good share of the sun before it reaches you at four in the afternoon.

It also cuts the UV landing on floors and furniture. NFRC puts UV at roughly 40 to 60 percent of fading damage, so this slows fading rather than stopping it.

View and glare controlSlows fading

Solar, 3 percent openness

A tighter weave. The room goes dimmer and the view drops back to an outline. Choose it where the sun is the problem and the view is second, which around here usually means a west wall in July. That's a common call on this side of Indianapolis.

Openness affects how much you see out, not how private you are. A 3 percent fabric still shows silhouettes at night.

View becomes an outlineStrong glare control

Solar, 1 percent openness

Close to a solid fabric with a little view left in it. This is the strongest glare control in the solar family.

The trade is that it darkens the room on a gray January day too. Indianapolis averages a January high near 36F and the light is flat, so think about how the room reads in both seasons before you commit.

Darkest solar optionDim on gray days

Light filtering

No view through it. Daylight comes through the face diffused, so the room stays bright without a hot spot across the television or the kitchen island. This is the default for living spaces.

It isn't private in reverse at night. With the lamps on and the sun down, silhouettes still show.

No view through itBright without the glare

Room darkening

A denser fabric, usually with a liner behind it. Most of the light coming through the face is gone.

Light still arrives around the edges on an inside mount, so a room darkening shade gives you a dim room rather than a dark one. If someone in the house sleeps during the day, say so at the measure and we'll scope it differently.

Dim, not darkEdges stay bright

Blackout

The fabric itself passes essentially no light. What you'll still see is the perimeter. Lutron publishes an inside-mount light gap of about 3/4 inch per side on its Roller 20 and 64 shades, along with a standard factory deduction of 1/16 inch per side, and shades over 120 inches tall or past a 4:1 height-to-width ratio get larger gaps than that.

So if you need a genuinely dark bedroom, that gap has to be dealt with on purpose, either with side channels or by going outside mount. We tell you which one your opening can carry while we're still standing in the room.

Dark facePerimeter needs a plan

Openness factor is a measured fabric spec, so you can compare it line to line. The category names are not measured. One maker's room darkening can behave like another maker's light filtering, which is why the sample books come to the measure and get opened in the room they're going in, at the hour that room has the problem.

Common Questions

Pleated Shades FAQ

Questions we hear most often from Mooresville homeowners considering pleated shades.

One layer against two. A pleated shade is a single sheet of fabric creased into folds. A cellular shade joins two faces so each fold encloses a pocket of still air, and that pocket is the whole reason for the price difference. DOE and Oak Ridge measured cellular shades saving up to 20 percent of heating energy compared with a bare window, and that measurement belongs to the cell, not to the crease. Visually they're close enough at a distance that most people can't tell them apart on a wall. Functionally, in a Mooresville January with an average low of 20.9 degrees, they're different products.
A little, in the way any fabric across an opening does, and not enough to buy it for that. Anything hanging in front of the glass slows the movement of air against it and takes the edge off the cold you feel sitting nearby. That's a comfort effect rather than a measured one, and we won't put a number on it because no number exists for this product. If reducing winter loss is the actual goal in a 1965 ranch, a double cell cellular in side channels is the honest recommendation and we'd rather sell you that than oversell this.
They soften, which shows first at the bottom where the folds carry the most weight. A pleated shade cycled daily for a decade hangs with less definition than it did new, and the fabric can develop a slight wave across its width. The ones still hanging in the 198 houses Mooresville built through the whole of the 1980s show exactly that. None of it stops them working. It does mean a pleated shade in a room you use constantly ages faster than the same shade in a guest room. Where somebody wants a crisp look to survive heavy daily use, a cellular holds its shape longer because the cell structure supports the fold.
Secondary rooms with real openings and a modest budget. A back bedroom, a home office in a converted 1970s den, a stair landing, the small openings in a compact three bedroom plan where a heavier product looks overbuilt. It stacks very tight at the top, so on the short wide openings that define the 1960s ranch stock it hands back more glass than a Roman or a woven shade. National ranges put stock shades at roughly $60 to $600 per window against $250 to $2,600 for custom, and a custom pleated shade sits low in that custom band.
Both are available and both change the product. Cordless removes the cord and gives you a shade you push and pull by the bottom rail, which suits a house with children and costs more. Top down bottom up adds a second lift path so the top rail can drop, which is genuinely useful on a street facing opening in the 320 houses here that predate 1940. What both do is add mechanism to a product whose main virtue is simplicity, so on a low cost secondary opening the plain corded or cordless version is usually the better buy.
The fabric takes the load and shows it eventually. A west opening in Mooresville gets full afternoon sun from roughly three o'clock onward through the summer, and a single layer of light fabric in that position will change color over years. Fade is slowed by any covering rather than prevented, with NFRC attributing 40 to 60 percent of fade damage to UV. A light face outward reflects more than a dark one and ages better. If a west room is the main problem, a solar mesh or an exterior product does more for the room than any pleated fabric will.
Structure. A pleated shade is a single layer of fabric folded into pleats, so when you look at the edge you see one accordion. A cellular shade is two layers joined so the folds form closed cells, and when you look at the edge you see honeycombs with air inside them. That trapped air is the entire point of a cellular shade. A pleated shade doesn't have it, which is why it costs less and why we don't make an energy argument for it.
Not the way a cellular does, and we won't pretend otherwise. Any fabric between you and cold glass in a Mooresville January does something, since it slows the air movement at the window and takes the edge off a draft you can feel from the couch. What it doesn't have is the trapped air pocket. The DOE and ORNL testing that gets quoted in this trade, up to 20 percent heating energy savings and up to 15 percent of total heating and cooling energy, was done on cellular shades. If that number is why you're buying, buy cellular.
When the room needs a good-looking shade rather than an energy product. Secondary bedrooms, home offices, hallways, a bonus room over a garage, a rental between tenants, a house being prepared for sale. All of those want something that fits the opening properly and costs sensibly. Pleated does that. It's also the right answer on arched and angled openings where no other product follows the shape, and that has nothing to do with budget.
Mostly, and they do soften. A pleated shade holds its folds because the fabric was heat-set at the factory, and that set relaxes slowly, faster on a hot window than on a shaded one. After several years on a west-facing Mooresville window you may see the folds sit slightly less sharp than they did, particularly at the bottom of the shade where it spends most of its life stacked. A cellular shade holds its shape longer because the cells brace each other. That's a real difference worth knowing.
Because the lift cord runs through holes punched in the fabric. On a corded pleated shade, each pleat has a small hole for the cord to pass through, and with the shade down those holes stack into a vertical line of bright dots that you notice at night and barely see during the day. It's construction, not damage. Cordless lift removes them entirely, since there's no cord passing through the fabric, and that's one of the better reasons to spend the difference.
In any room a child or a pet uses, yes, and we specify it that way. There's no operating cord on the product at all, which is the direction the ANSI/WCMA A100.1-2022 work on cord access points, and inner-cord non-compliance is treated as a substantial product hazard under 16 CFR 1120.3. On a pleated shade there's a second benefit, which is the route holes disappearing. The tradeoff is cost and the fact that a wide unit wants a hand at each end of the bottom rail rather than one in the middle.
Dim, not dark, and the reason is the edges rather than the fabric. A room darkening pleated fabric blocks most of the light through its face. What it can't do is close the gap down each side of an inside mount, and Lutron publishes 3/4 inch per side as a real inside-mount figure on their roller product to give you a sense of the scale. For a genuinely dark bedroom the answer is an outside mount with real overlap, or a blackout fabric running in side channels, which is a different product.
Yes, and pleated is usually what those get built from. A half-round over a front door, a quarter-round in a stairwell, an angled top following a vaulted ceiling: all of them get a site template, and the shade is fabricated as a fixed fan to that pattern. Fixed means it doesn't operate, which surprises people, so we say it early. If the shape has to move, the honest answer is often a movable shade below the straight line and a fixed unit above it.
Less than most products, and not nothing. A raised pleated shade gathers into a compact stack at the headrail, smaller than a double cell shade of the same height and much smaller than a woven natural. On a tall window that stack is a couple of inches of glass. On a short window it's a bigger share of the view, which is why we measure the drop and tell you where the bottom rail will actually sit when the shade is fully up.
Dust them and leave them alone otherwise. A vacuum on low with a brush head across the face, or a soft duster run along the folds, handles routine dirt. Spot marks come off with a barely damp cloth blotted, never rubbed hard, because the fabric is thin and the heat-set folds don't like being worked. Don't submerge them, and don't use a steamer on them. Fabric that has been soaked tends to come back with soft folds that never recover their line.
Reasonably, with the usual honesty about the exposure. A west or south window in Morgan County takes real sun from late May into September, and a light colored pleated fabric there will soften in color over the years more than the same fabric on a north window. A reflective backing helps the fabric itself and improves how the shade looks from the street, since all the shades read the same color from outside. On the room behind it, NFRC puts UV at roughly 40 to 60 percent of fading damage, so the shade slows what happens to your floors. It doesn't end it.
Wide enough for most rooms, with weight and headrail deflection as the limits. Pleated fabric is light, so the fabric itself isn't the constraint. What matters is the headrail across a long span and the way a wide bottom rail behaves when you lift it from one end. Past the point where a single unit gets awkward, two shades sharing an opening reads better than one that drags. We work that out at the measure rather than after the box arrives.
Close, and possibly not exact. Pleated fabrics run in dye lots, so a shade woven this year can sit slightly off one woven three years ago. Across a hallway nobody sees it. On two windows in the same wall everybody does. The practical advice is to do a room in one order, even the small window you were going to skip. We write the fabric name and color onto your paperwork so a later order at least starts from the right reference.
Two to five weeks is the normal custom fabrication window, and pleated usually sits at the shorter end because it's a simple build. Templated arches and angle tops run longer, since somebody is making a one-off to your pattern. The window goes into your paperwork along with the scope, the dates and the total price, which the Indiana Home Improvement Contract Act requires on residential work over $150.
Areas We Serve

Pleated Shades Across Mooresville

We measure and install in every one of these Mooresville neighborhoods. Each has its own page with the build eras, window conditions and mounting notes for that section.

Related Services

Other Window Treatment Services in Mooresville

Mooresville Window Treatments handles the full scope of window treatment work. Explore our other services below.

Faux Wood Blinds in Mooresville

The slat that ignores a Morgan County August

Learn more →

Wood Blinds in Mooresville

Basswood where the casing earns it

Learn more →

Vertical Blinds in Mooresville

The wide door answer that still works

Learn more →
Free In-Home Measure

Schedule Your Free In-Home Measure in Mooresville

Contact Information

Reach Us Directly

Our team prioritizes scheduled measures and service calls, and books in-home measures during business hours.

Office
1417 Commerce Avenue, Indianapolis, IN 46201
Hours
Mon-Fri 8a-6p
Service Area
Mooresville, IN and Surrounding Areas

Ready to Book Your Measure?

Call us to set up an in-home measure, or to ask about a treatment that has stopped working. We will talk it through on the phone first.

Call (317) 999-5154
Service area

Serving Mooresville and the surrounding area

Call NowGet Quote